Table of Contents

Isolated UART Circuit: Signal Direction, Power and Grounding

Two unconnected development boards and a loose eight-pin IC on an electronics workbench

An isolated UART circuit needs one signal channel in each direction for full-duplex communication. Each transmitter drives an isolator input in its own power domain. Across the barrier, the corresponding output drives the other device’s receiver. Power each half of the isolator relative to its local ground.

Start a schematic review with a single question. When the host sends a byte, which physical pin on the remote controller receives its start bit? Trace that path in ink, then trace the reply in a second color. This catches two errors that can survive a visual inspection of a tidy schematic: an output connected to another output, and a connector pin labeled TX from the opposite board’s perspective.

Trace the outgoing byte and its reply

Consider a host MCU on side 1 and a peripheral MCU on side 2, each exposing a conventional, non-inverted logic-level UART. The example uses TI’s ISO7721DR in the eight-pin D package. In this orientation channel B carries the request and channel A carries the reply. The letters identify channels inside the chip. Net names such as HOST_TX and REMOTE_RX identify the endpoints on the board. TI ISO772x datasheet, Figure 5-4 and Table 5-1

TrafficLocal driverIsolator inputIsolator outputDestination
RequestHost TXPin 3, INBPin 6, OUTBRemote RX
ReplyRemote TXPin 7, INAPin 2, OUTAHost RX
Host TX through INB pin 3 and OUTB pin 6 to remote RX; remote TX through INA pin 7 and OUTA pin 2 to host RX
For this D-package part, channel B carries host TX to remote RX. Channel A carries the reply.

The isolator reproduces a logic state across the barrier. The UART peripherals at the endpoints still generate and decode the frame. If the board also routes RTS, CTS, reset or an interrupt across the boundary, add a row for each signal and count the required channels by direction. Two channels cover only TX and RX in this example. TI’s UART isolation example, Figure 1-1

Check what the connector actually exposes. An RS-232 port requires an appropriate line transceiver between its cable signals and logic-level pins. With a USB-to-UART adapter, identify the adapter’s logic-side TX, RX, voltage level and ground before treating it as a UART endpoint. For ordinary UART connections and frame settings, see the UART hardware guide.

Give each side a local supply and return

On this package, connect VCC1 (pin 1) and GND1 (pin 4) to the host domain. VCC2 (pin 8) and GND2 (pin 5) belong to the remote domain. The ISO7721DR transfers signals across the barrier. Its remote side needs a power source of its own. That can be an existing supply in the remote equipment or the secondary output of a suitably rated isolated converter. A second regulator fed from the host with a shared return still leaves a conductive path between domains. TI’s UART isolation overview

Host rail and return connect to VCC1 and GND1; remote rail and return connect to VCC2 and GND2 on ISO7721DR
Each local voltage is measured against its own return. The drawing identifies the four supply and ground pins.

Suppose the host uses 3.3 V I/O and the remote MCU uses 5 V I/O. Before assigning those rails to the isolator, record their minimum and maximum voltages at the pins. Check the recommended supply range on both sides. Then compare each driver’s guaranteed output levels with its local receiver’s input thresholds at the intended load. The return path needs the same check as the request path. Fit each supply’s bypass capacitor close to its supply and local ground pins as shown in the selected device’s layout guidance. TI ISO772x datasheet, Sections 6, 10 and 11

A useful power-tree annotation is “what supplies VCC2 when the host USB cable is unplugged?” Answer it for normal operation and for service mode. A bench setup can appear to work while a debug accessory powers a rail that the installed system must supply itself.

Follow the ground paths through the test setup

Draw a boundary through the signal isolator and the isolated supply, if fitted. Follow every other connection that leaves either domain. Include cable shields and their terminations, programming headers, mounting hardware bonded to chassis, USB adapter grounds, bench supplies and instrument leads. Mark intentional chassis or protective-earth connections according to the equipment design. If two points drawn with separate ground symbols meet through a cable, the assembled system has a return path the schematic symbols alone do not show. TI Digital Isolator Design Guide, Sections 2 and 4

Unplugged USB cable, loose oscilloscope ground clip and an unpowered circuit board
A USB cable or a probe ground lead can add a return path. Trace those connections before attaching the instruments. AI-generated bench scene.

For example, a host board and a remote USB-to-UART adapter may both plug into the same PC. Trace the ground path through both USB connections and check whether the adapter provides isolation. If connecting a laptop changes the UART behavior, record the connected and disconnected configurations before changing firmware.

Make measurements with the instrument’s reference connections understood. On many bench oscilloscopes the passive probe ground clips share protective earth. Connecting those clips to opposite domains can join the domains through the instrument. Keep protective earth intact and use appropriately rated differential or isolated measurement equipment where the reference potentials require it. Check the probe and instrument limits for the actual setup. Tektronix guidance on floating measurements

Check what the receiver sees during startup

A conventional non-inverted UART idles high. A frame begins with a low start bit and ends with a high stop bit. A receiver enabled while its input drops low during a power transition may see a candidate start bit. Whether it accepts a character, signals a framing error or discards the event depends on the waveform and the receiving UART. Microchip USART frame formats

Circuit board and disconnected test leads on a bench prepared for power-sequence checks
Record which domain powers up first and when its UART receiver is enabled. AI-generated bench scene.
State to reproduceWhat to record at the receiving MCU
Receiver powered first, transmitter side offLocal RX level after the isolator’s specified default-state conditions are met
Transmitter side powering upRX transitions before and during transmitter pin configuration
Both sides readyIdle level, then the first deliberately transmitted byte
Transmitter side resets or loses powerAny low interval and the receiver’s framing, break or data flags

Run the sequence with the roles reversed if either endpoint can restart independently. A high-default option may suit an idle-high link while the input side is unpowered. Once the input side is valid, its actual input level matters, including the MCU pin’s reset configuration. Check the exact isolator function table before deciding whether the design needs a local bias resistor or a firmware delay before enabling reception. Digital isolator default states and power loss

Diagnose a silent or one-way link

Start with a repeated known byte such as 0x55. In an 8-data-bit frame its alternating bits provide visible edges. Capture the same transmission at the sending TX, the isolator input, the corresponding output and the receiving RX, using a suitable reference at each point. The first location where the expected pattern disappears narrows the fault to one segment.

Oscilloscope with dark display, disconnected probe and unpowered logic board
Follow a known byte from transmitter to receiver and compare each accessible node against its local reference. AI-generated bench scene.
SymptomFirst comparisonNext check
Remote receives requests, host gets no replyRemote TX and the return-channel inputConfirm firmware sends a reply. Then follow the return output to host RX.
Input toggles, corresponding output stays fixedOutput-side supply against its local groundCheck the package pin map, power state and function table.
Edges reach RX, decoder reports framing errorsRaw RX waveform and configured frameVerify idle polarity, bit period, baud setting, parity and stop bits.
First byte is wrong only after power cyclingRX around reset release and receiver enableCompare the event with both supply ramps and the first intended transmission.

A timing example. Assume 115,200 baud and 8N1. Each bit occupies about 8.68 µs. One start bit, eight data bits and one stop bit occupy about 86.8 µs on the wire. These figures help set the capture window. A gap between successive bytes adds time to the transaction. A nearly constant isolator delay shifts the frame’s arrival, while unequal rising- and falling-edge delays can change individual pulse widths. For an asynchronous receiver synchronized by the incoming start edge, these effects deserve separate checks.

For handoff, record the exact device and package, the two traced paths, both rail ranges, the intended idle level and the startup capture that exercises the more difficult power sequence. If the circuit review leaves multiple candidate isolators, use the ISO7721 and ISO6721 selection comparison to check supply windows, channel assignments and ordering suffixes.

Engineering basis, 19 November 2026. The pin example follows TI’s catalog ISO7721 D-package top view. The timing values are calculated from the assumed UART format. The troubleshooting sequences are proposed checks for the reader’s hardware.